| DTP T UWP 232 D |
| NOTE | *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output. |
|
|
| Video |
|---|
| Maximum data rate | 6.75 Gbps (2.25 Gbps per color) |
| Maximum pixel clock | 165 MHz |
| Resolution range | Up to 1920x1200 or 1080p @ 60 Hz; 8 bit color depth
2048x1080p @ 60 Hz (2K) |
| Formats | RGB digital video |
| Standards | DVI 1.0, HDMI, HDCP 1.2, EDID 1.3, CEA-861E |
|
| Video input — HDMI |
|---|
| Number/signal type | 1 single link HDMI (or DVI-D*) input |
| Connectors | 1 female HDMI type A |
|
| Video input — VGA |
|---|
| Number/signal type | 1 analog RGBHV |
| Connectors | 1 female 15-pin HD (RGB) |
| Nominal level | 0.7 Vp-p for RGB |
| Minimum/maximum levels | 0.3 V to 1.45 Vp-p |
| Impedance | 75 ohms |
| Horizontal frequency | 15 kHz to 130 kHz |
| Vertical frequency | 30 Hz to 150 Hz |
| Return loss | <-30 dB @ 5 MHz |
| DC offset (max. allowable) | 250 mV |
|
| Interconnection between transmitter and receiver |
|---|
| Signal Type | 1 DTP 230 output |
| Connectors | 1 female RJ-45 |
| Termination standards | TIA/EIA T568B |
| DTP signal | |
| Signal transmission distance | Up to 230' (70 m) using shielded twisted pair (STP) cable or XTP DTP 24 cable |
| Cable requirements | Solid conductor, 24 AWG or better |
| Cable recommendations | 400 MHz bandwidth STP cable |
| NOTE | Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. |
|
|
| Audio |
|---|
| Gain | Unbalanced output: 0 dB; balanced output +6 dB |
| Frequency response | 20 Hz to 20 kHz, ±0.5 dB |
| THD + Noise | 0.03% @ 20 Hz to 20 kHz at maximum output |
| S/N | >90 dB, at maximum output (15 dBu), balanced (unweighted) |
| Stereo channel separation | >80 dB @ 1 kHz to 20 kHz |
|
| Audio input |
|---|
| Number/signal type | |
| Analog audio (over DTP) | 2 stereo, unbalanced |
| Digital audio | 1 embedded digital audio on DTP |
| Embedded digital audio source formats | 2-ch PCM, PCM, Dolby Digital 2/0, Dolby Digital 2/0 Surround, Dolby Digital 5.1, Dolby Digital EX, DTS Digital Surround 5.1, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1 |
| Connectors | (2) 3.5 mm stereo jack, 2 channel; tip (L); ring (R); sleeve (ground) |
| Impedance | >10k ohms, DC coupled |
| Nominal level | -10 dBV (316 mVrms) |
| Maximum level | +7 dBu, unbalanced |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio output |
|---|
| Number/signal type | |
| Analog audio (over DTP) | 1 stereo, unbalanced |
| Digital audio | 1 embedded digital audio on DTP |
| Embedded digital audio source formats | 2-ch PCM, PCM, Dolby Digital 2/0, Dolby Digital 2/0 Surround, Dolby Digital 5.1, Dolby Digital EX, DTS Digital Surround 5.1, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1 |
| Connectors | 1 female RJ-45 jack |
|
| Communications — transmitter |
|---|
| Serial control port | RS-232 via (1) 3.5 mm, 5-pole captive screw connector for RS-232 control (±5 V) and contact closure input switching |
| Baud rate and protocol | 9600 baud rate, 8 data bits, 1 stop bit, no parity |
| Contact closure remote control | (1) 3.5 mm, 5-pole captive screw connector (connector is shared with RS-232 control port) |
| USB control port | 1 front panel female mini USB type B |
| USB standards | USB 2.0, high speed |
| Program control | Extron Simple Instruction Set (SIS™) |
|
| Communications — external device (pass-through) |
|---|
| Serial control pass-through port | Bidirectional RS-232 |
| Connector | |
| DTP output | (1) 3.5 mm captive screw connector, 5-pole |
| Baud rate and protocol | 300 to 115200 baud, 8 or 7 data bits, 1 or 2 stop bits, non-parity (default), even or odd parity |
| IR pass-through control port | TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz |
| DTP output | (1) 3.5 mm captive screw connector, 2-pole |
| NOTE | Protocol is mirrored between the connected DTP 230 or DTP 330 endpoints and the "Over DTP" ports on the DTP T UWP 232 D. Signals from a control device pass into each "Over DTP" port, are embedded with the DTP signal and sent to the individual DTP 230 Tx or Rx endpoints for control of remote sink or source devices. |
|
|
| General |
|---|
| Power supply | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts |
| Power consumption | |
| Transmitter | |
| Device | 4.8 watts, 12 VDC |
| Device and power supply | 6.3 watts, 100-240 VAC, 50-60 Hz |
| NOTE | Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable. |
|
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, no vents |
| Thermal dissipation | |
| Transmitter | |
| Device | 15.3 BTU/hr |
| Device and power supply | 20.1 BTU/hr |
| Mounting | |
| Rack mount | Yes, with included rack ears |
| Enclosure type | Metal |
| Enclosure dimensions | |
| Faceplate | Two 2.6" H* x 1.3" W x 0.2" D
6.6 cm H x 3.3 cm W x 0.6 cm D
(Fits the opening in a 2-gang decorator wallplate.) |
| Device | Two 2.7" H x 3.5" W x 1.9" D
6.9 cm H x 8.9 cm W x 4.8 cm D |
| NOTE | *Height is 4.2" (10.4 cm) including mounting tabs. |
|
| Product weight | 0.4 lbs (0.2 kg) |
| Regulatory compliance | AS/NZS, c-UL, C-tick, CE**, FCC Class A**, ICES, UL, VCCI
Complies with the appropriate requirements of RoHS, WEEE |
| NOTE | **CE and FCC testing is conducted with STP cable. |
|
| Product warranty | 3 years parts and labor |
| Everlast power supply warranty | 7 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (4460-092818) |